Archive for the ‘HOWTO’ Category

DIY Arduino water meter with iPad display

Saturday, November 6th, 2010

TEAGUE Give Water from TEAGUE on Vimeo.

It’s another arduino stuff to be working on here. All related references are included:

Some of the folks over at Teague Labs have been noodling around with measuring water consumption. They’ve built a graphing water meter using a YellowJacket Arduino board with built-in WiFi and coolant flow meter from a PC cooling system to see how they used water around the office. Water conservation is major concern in many areas around the world. Tools that allow us to observe and correct our behaviors help us towards a path to sustainability. Schematics and source code are available if you want to try it out for yourself.

courtesy: Adam

It’s an Arduino-based speed detector

Saturday, November 6th, 2010

Flash / Arduino Based Speed Detector from Mike Chambers on Vimeo.

Mike Chambers built this excellent looking arduino-based speed detector. An Arduino measures the time it takes an object to travel between two points, which is then relayed back to a computer (or smart phone), where it is converted into average speed and presented in a clear manner. The concept for the project is simple, however he wins big points for putting it all together into a working package.

courtesy: Arduino Blog

Modem used in an alarm system

Sunday, August 29th, 2010

ORP Systems

This alarm system senses motion and then alerts you by phone. And this fellow, [Oscar] had an old external modem sitting around and, with some wise hardware choices, he came up with a simple circuit to use it. First up is the PIC 16F628A chosen because it doesn’t require an external crystal. This connects with the modem via a DS275 RS232 transceiver because it requires no external parts for connection. The final portion of the puzzle is a PIR sensor that triggers a pin interrupt in the sleeping PIC, which then dials your number to alert you. It doesn’t look like anything happens other than your phone ringing, but that’s enough for a simple system. We’re glad to see how easy it was to use that modem… time to go hunting for one in dreaded junk trunk. Don’t miss the clip after the break.

What you can see in the video is: The modem is turned on and the pic configures it to disable command echo, change to return numeric responses and turn off the volume of the modem speaker. The user has 15 seconds to leave the room, then the pic waits a motion detection. When it is detected the pic dials a fixed phone number and the user will receive the alert.

The pic is programmed in CCS and the source code is included. Well, I bet it’ll be a great project to make. ^_^

Source ORP Systems

Open source satellites

Thursday, May 6th, 2010

machineSat.jpg

After three years of research and one year of experience as a satellite engineer, Song Hojun has found that it is possible to launch and operate a personal satellite at a fairly reasonable price. In addition, he has for the past five years been exploring ways to integrate the concept of a personal satellite project into cultural contexts and into his artistic practice.

mpSatEvent.jpg
All the satellite-related systems (except for the rocket to launch it) are DIY programs — designed so that regular people may also have the chance of developing and eventually launching their own.

Song have presented this system and how it works at the Machine Project, Los Angeles on 2010, 25th April.

For the people who want to study or getting a clearer picture of the involving mechanisme, they can download Song’s book from Google Books here.

Courtesy: Open Source Satellite Initiative via Make

Do It Yourself a RFID immobiliser

Sunday, May 2nd, 2010

rfid-car-immobiliser

This guy, [andrew_h] has put together this slick anti theft device for his car. This RFID immobiliser is used to keep the car engine from starts unless you swipe an RFID tag. Depending on how well you hide it, and how well the person stealing the car knows you, they would have no reason to suspect that they have to swipe the tag. Even if someone steals the car while it is already running, they won’t be able to re start the engine if they shut it off. Guys, you should try this one if you have any car to experiment with, or you have to steal a car to do this.. kidding! All steps, schematics and PCBs are available.

Available at Instructables.com via Hack A Day

Build a 9-digit Pulse Counter for under $20

Sunday, May 2nd, 2010

pulsecounter.jpg

Roughly, at $20 to build? This 9 digit pulse counter is an excellent example of home built tools. Josh, the builder found himself repairing a device and in need of a pulse counter. With the components cheaply available, he just built his own. He says that it has a few limitations, like display brightness, but overall it seems to do the job well. All the stuffs, steps and even PCB can be downloaded from his site at your own will.

Courtesy of Imsolidstate

How to decode infrared transmission

Thursday, April 22nd, 2010

rc5-decoding-explained.jpg

Alright, here we’re going for chapter on Manchester Encoding. Brian J Hoskins did just that when building this RC5 decoder. This protocol is widely used in television remote controls. You use them on a daily basis, don’t you think it’s time you understood what’s going on? Check out his writeup and learn the dark art of invisible light communication. Or just skip the learning and follow this how-to.

courtesy: Hack a day

How to build your own RFID reader

Thursday, April 22nd, 2010

DIY RFID

Do you have any idea on how easy it is to build your own RFID reader? Well, we stumbled upon some sites that’ll give you some clearer picture on how to make this thing happens. As pointed out by hackaday,

[Klulukasz] left a comment pointing to this DIY RFID reader that was a final project in 2006 for a class at Cornell University. It is well documented and includes not only a schematic and code, but an explanation of the design considerations used during the build. The project uses an ATmega32 and the parts list priced out at about $50 at the time. There were plenty of responses to theRFID spoofer post pointing out that there are readers available for $40, but we want the fun of building our own.

A bit more vague with the details but no less interesting is this other simple RFID reader design.

Courtesy: hackaday

Radio monitoring book re-released under a Creative Commons license

Wednesday, April 21st, 2010

skips-book.jpg

Make contributor T.J. “Skip” Arey says:

Many of you know that, some time back, I authored a book called Radio Monitoring — A How To Guide. Originally published by Index Publishing Group and later released by Paladin Press, is had two very successful editions that sold for many years. This book has recently gone out of print but I am pleased to say that I have now released it on line (for FREE) via Creative Commons license. I admit that a few points are a bit dated but the book still has a lot to offer the beginner or even experienced radio hobbyist. You can download a copy thanks to the North American Shortwave Association (NASWA) who have consented to be the primary online source for distribution. The hobby has been good to me over the years. I am happy to give this book back to the radio community. Enjoy.

Courtesy: Naswa.net via Make

Automated rain barrel watering system

Tuesday, April 20th, 2010

automated-garden-watering.jpg

To some crowds, irrigating a small garden is a relatively relaxing and sometimes therapeutic activity, well if you are a botany/biology nerd or desperately really need a hobby – but going away for any length of time can present a problem. The simple solution of course is to purchase a hose-bib/timer package from Home Depot for about $30 and set up a small drip system to efficiently water each plant or row of plants (rather than a wasteful sprinkler system). Going along with conserving water is using a rain barrel collection system to capture rain for later use thus eliminating or more likely reducing treated water consumption.

Adding a rain barrel complicates the system significantly as there isn’t much water pressure at its spigot compared to a standard city spigot which has somewhere around 40 psi. Also, if the barrel is empty, you don’t want your plants to die and thus you need to be able to detect that the barrel is empty and switch to city water.

Courtesy: HAXORYOURMOTHERHARDRIVE